Opens in a new tab
Kaolin
JACAN Powder Equipment
Insights

What Are The Common Causes Of Blockages In A Kaolin Pneumatic Conveying System?

Pneumatic conveying is widely used to transfer fine kaolin powder between silos, mills, classifiers, modification reactors and packaging units in kaolin processing lines. Blockage is one of the most frequent operational failures, which interrupts continuous production, increases cleaning workload and may trigger material degradation. Based on kaolin-mill.com kaolin processing experience, the root…

Pneumatic conveying is widely used to transfer fine kaolin powder between silos, mills, classifiers, modification reactors and packaging units in kaolin processing lines. Blockage is one of the most frequent operational failures, which interrupts continuous production, increases cleaning workload and may trigger material degradation. Based on kaolin-mill.com kaolin processing experience, the root causes can be sorted into material properties, system design, operating parameters and equipment faults.

1. High moisture content of kaolin powder

This is the top cause for kaolin conveying blockages. Kaolin has abundant surface hydroxyl groups and strong water absorption. If the powder is not fully dried, or absorbs moisture from humid ambient air during storage and transfer, fine particles become sticky. Wet kaolin adheres to the inner wall of pipelines, gradually builds up layered deposits, and finally narrows or fully blocks the pipe. Modified kaolin with organic coupling agents is more sensitive: moisture can trigger partial hydrolysis of modifiers and make powder stickier.

2. Improper air velocity

Pneumatic conveying relies on a minimum transport velocity to suspend kaolin particles.

  • If air speed is too low: fine kaolin particles settle out of the air stream, slide and accumulate at the bottom of horizontal pipes, bends and elbows. This is the classic sedimentation blockage.
  • If air speed is excessively high: strong particle-wall friction generates heat, and soft modified kaolin may turn sticky, forming wall accretion. High velocity also accelerates pipe wear and produces more fine agglomerates. Kaolin requires a stable velocity window, different from coarse mineral powder.

3. Presence of agglomerates and oversized particles

Drying cakes, hard lumps formed during storage, unbroken agglomerates from the modification reactor, or coarse gangue fragments cannot be suspended normally. These large clusters easily get stuck at elbows, reducers, diverter valves and receiving bin inlets. Even small agglomerates can accumulate gradually and develop into a full plug.

4. Unstable feeding and inconsistent material loading

Overfeeding into the conveying pipeline exceeds the designed solid-gas ratio. When too much kaolin powder enters the limited air flow, the air cannot carry all particles, and sedimentation occurs quickly. Intermittent feeding is also problematic: pulse surges of material create dense slugs that are hard to fluidize. On the contrary, discontinuous feeding may let the air blow through without material, followed by sudden material accumulation.

5. Poor pipeline layout and unreasonable structure

Kaolin blockages tend to concentrate at special pipe sections. Sharp elbows, long horizontal runs without upward lift, sudden pipe diameter expansion, poorly designed Y-tees and valve dead zones are high-risk spots. Slow-moving powder deposits at these positions. Internal rough weld seams, burrs or damaged lining also act as starting points for powder adhesion.

6. Air quality issues

Moist hot compressed air or carrier air carries water vapour. When warm humid air meets cooler pipe walls, condensation happens. Water droplets contact kaolin powder and create sticky wall deposits. Oil contamination from air compressors is another hidden trouble: oil mixes with kaolin fines and forms a hard, sticky cake that is difficult to remove.

7. Equipment and auxiliary component failures

  • Air filter blockage reduces air supply volume and pressure;
  • Air blower/fan performance degradation leads to insufficient conveying pressure;
  • Rotary airlock leakage: air backflow disturbs material flow and causes powder bridging above the feeder;
  • Diverter valve, butterfly valve or flexible hose jamming;
  • Build-up inside cyclone receivers or dust return lines.

8. Wrong process for modified kaolin grades

Surface-modified kaolin has different flow characteristics. Over-modified kaolin with free coupling agent has increased tackiness. If the conveying parameters are copied from raw hydrous kaolin without adjustment, wall sticking and blockage happen much more easily.

Common preventive measures include controlling powder moisture below the specification limit, maintaining the designed transport air velocity, installing lump breakers before feeding, optimizing pipeline layout with smooth long-radius elbows, using dry oil-free carrier air, and adding purge air points at high-risk sections. Regular wall inspection and purge cycles help avoid progressive deposit buildup.

Written by
SEO
Free Custom Process Solution
We specialize in dry ultrafine processing R&D and share practical technical insights for buyers worldwide. Contact us now to get your free tailored process proposal.
I Need Solutions
JACAN Powder Equipment

More Insights

Explore professional perspectives and technical breakthroughs in ultrafine grinding.

How To Reduce Energy Consumption In A Kaolin Grinding Plant

Energy consumption is one of the largest operating costs for kaolin grinding lines. Power is…

How To Perform Routine Inspections Of A Kaolin Surface Modifier

Routine inspection of the kaolin surface modification system prevents inconsistent modification degree, powder agglomeration, free…

Can a PLC control system be integrated with kaolin equipment?

Yes, PLC (Programmable Logic Controller) control systems can be fully integrated into modern kaolin processing…

How To Automate A Kaolin Grinding And Classification System

Automation of kaolin grinding and classification aims to stabilize particle size distribution (PSD), preserve platy…

Chat with us