Opens in a new tab
Kaolin
JACAN Powder Equipment
Insights

What Is The Optimal Particle Size Of Kaolin For Paper Coatings?

The optimal particle size of kaolin for paper coatings depends on the target paper grade, gloss requirement, coater speed and coating formula. For mainstream hydrous kaolin coating pigments, the industry standard target is D50: 0.5–2.0 μm, with 85–95% of particles below 2 μm and a strict top cut (D97) below 5 μm to…

The optimal particle size of kaolin for paper coatings depends on the target paper grade, gloss requirement, coater speed and coating formula. For mainstream hydrous kaolin coating pigments, the industry standard target is D50: 0.5–2.0 μm, with 85–95% of particles below 2 μm and a strict top cut (D97) below 5 μm to minimise blade abrasion and surface scratches.

High‑gloss art paper, magazine coated paper and high‑speed offset printing grades use the finer end of this range: D50 = 0.5–1.2 μm, typically with 90%+ below 2 μm. Fine, thin platy kaolin aligns parallel to the base sheet during calendering, building a dense, smooth surface that boosts gloss, ink holdout and print sharpness. The main trade‑off is higher slurry viscosity and greater binder demand, which limits maximum solids content and can raise running costs if not dispersed properly.

For semi‑gloss, matte coated board and general publication paper, the balanced, most widely used window is D50 = 1.2–2.0 μm, 85–90% below 2 μm. This grade delivers a good compromise among gloss, smoothness, opacity, rheology and binder consumption. It runs more stably on high‑speed blade coaters, supports higher coating solids, and reduces the risk of dilatant behaviour or streaks at the coating blade.

Coarser kaolin (D50 > 2.5 μm) is generally not suitable for top coating; it creates rough surfaces, lowers gloss and increases wear on coating blades and printing plates. Overly ultrafine kaolin (large fractions below 0.2 μm) also has drawbacks: it pushes viscosity sharply, increases latex or starch binder uptake, and may hurt opacity by reducing controlled microvoids in the coating layer.

Particle size distribution is just as important as median size. A narrow PSD is preferred; wide distributions with coarse tails are the main cause of scratches and gloss variation. Platy shape factor must be matched with fineness — high‑aspect‑ratio kaolin develops gloss much better than blocky kaolin at the same D50. Calcined kaolin used for opacity boosting is usually formulated as a blend, often with slightly coarser or tailored sizing, not as the primary gloss pigment.

In practical formulation, mills rarely use one single kaolin grade. They blend fine gloss kaolin and mid‑size coating kaolin to tune gloss, porosity, ink receptivity and runnability for their specific coating colour and machine conditions.

Written by
SEO
Free Custom Process Solution
We specialize in dry ultrafine processing R&D and share practical technical insights for buyers worldwide. Contact us now to get your free tailored process proposal.
I Need Solutions
JACAN Powder Equipment

More Insights

Explore professional perspectives and technical breakthroughs in ultrafine grinding.

How To Reduce Energy Consumption In A Kaolin Grinding Plant

Energy consumption is one of the largest operating costs for kaolin grinding lines. Power is…

What Are The Common Causes Of Blockages In A Kaolin Pneumatic Conveying System?

Pneumatic conveying is widely used to transfer fine kaolin powder between silos, mills, classifiers, modification…

How To Perform Routine Inspections Of A Kaolin Surface Modifier

Routine inspection of the kaolin surface modification system prevents inconsistent modification degree, powder agglomeration, free…

Can a PLC control system be integrated with kaolin equipment?

Yes, PLC (Programmable Logic Controller) control systems can be fully integrated into modern kaolin processing…

Chat with us